

To other sifus out there you are welcome to correct any missteps or advise on improvements that can be done to get this router working with DDWRT. I also needed to switch from gateway to router in the Setup->Advanced Routing tab before it finally connected (DD-WRT v23 SP2 (09/15/06) std). At least this is what I did to get it working. Router: ASUS RT-N16 Description: NEWD K2. If all done correctly you will get working Unifi and hypptv and the other LAN ports can still be used for internet. This setup tutorial has been created, tested and is working on ASUS RT-N16 router, flashed with DD-WRT v24-sp2 (08/07/10) mega, (SVN revision 14896).
#Dd wrt v24 sp2 manual manual
Select manual for MTU and key in 1492 and apply settings. Unbridged eth0 and enable both multicast and masquerade/nat.Īfter reboot go to setup>basic setup>connection type and select PPPOE and key in your unifi credentials.
#Dd wrt v24 sp2 manual install
Download: : pro-v24sp2-20180: Readme for DD-WRT Firmware: Download: : 1.91: Readme for Buffalo firmware update: Download: 1.69 KB: : Commands to input in DD-WRT for Guest Network. dd wrt v24 sp2 10 10 09 std install Right in the instructions tells you exactly where to go and what to download.lso right on the wiki under install instructions.learly points you to the hardware specific section - again where you devices is listede honest - your just to lazy to bother doing any reading at all. Unbridged eth0.600 and enable both multicast forwarding and maquerade/nat. Includes documentation and quick setup guides for both Buffalo and DD-WRT firmware versions. This is to prevent mulitcast from flooding the wifi.Įbtables -A FORWARD -o ath0 -pkttype-type multicast -j DROPĮbtables -A OUTPUT -o ath0 -pkttype-type multicast -j DROPĮbtables -A FORWARD -o ath1 -pkttype-type multicast -j DROPĮbtables -A OUTPUT -o ath1 -pkttype-type multicast -j DROPĪfter reboot go to setup>networking and unbridged eth0.500 and enable masquerade/NAT. Swconfig dev eth0 vlan 4 set ports "0t 1t 5 6t"Īnd put this script in the same startup field again and click save firewall. Swconfig dev eth0 vlan 3 set ports "1t 6t" Hello, I just got my R7000 yesterday and installed DD-WRT v24-sp2 (03/07/15) kongac. Swconfig dev eth0 vlan 1 set ports "0 2 3 4" Setting a channel manually doesnt work for both eth1 and eth2. Put this script in administration>commands>startup then save startup Note that with this script you will get IPTV on LAN4 and other LAN ports still working for the internet. I manage a network of 9 routers running DD-WRT V23SP2 standard.ĭon't give up, and when it says to leave it 30 seconds (or 2 minutes) DO! Be patient.This is my startup script that I gather from searching and reading the DDWRT forum to get Unifi and HyppTV working nicely. There are many users worldwide using your WRT54G and GL routers with other than standard firmware, me included. Then you flash again, using the standard. Primary router is configured in a 192.168.1.X subnet and leases DHCP address in the same pool. Then you will (assuming you want to use DD-WRT firmware) need to flash a micro or mini firmware. In the case in which we are interested, a secondary router running DD-WRT v24 is configured as a Repeater Bridge between a Primary wireless router (of any make/brand/FW) allowing the above configuration. You will first need to establish which model router you have. I have only ever permanently killed one router - doing this. If you have to resort to the hard method of recovery, be careful. Following procedure works with firmware DD-WRT v24-sp2 (. Whenever you need answers they can be found here - However it describes too much and things that are not needed or even not working for the E3000 router.
